Metal button assembly guide

2010-3-6 15:56:04

1, the series of metal button products the right play:
To ensure the buttons on clothing products hit the best results, must be controlled from the following aspects:
1. Fabric choice, the choice of metal buttons
a.-shaped button, the fish eye button, emergency button, hit hit the nail usually jeans or casual clothes, the nail hit play 4-7 layer fabric, the remaining layer of fabric to play 2-4.
b. popper generally hit the cotton, the stapler suture position and should avoid the car side of the thick side of the thin fabric position.
2. To fight the system to do die
a. the surface mode to play mode shape should be matched with the product, when the product should be a clear bump Mai head a "follow-mode" to ensure that products are not deformed after playing.
b. play Mode's "volume position" should be able to ensure that products, such as surface flute flute mouth, and as far as possible the effective bending "non-flowering."
c. playing mode size should be matched with the product size, such as product diameter, height, etc., followed by the different products should be determined to fight mold materials, such as steel, sets of plastic mold, mold and other spring, once again, playing die mold body, Shank size should be used to hit the fuselage and the hole-button machine size matching, is strictly prohibited by the die method of foreign body wrapped handle mounted on the mold to play button.
3. Playing the adjustment mode
a. play mode button mounted on the machine, after playing the first Test empty, and then the fabric thickness adjustment according to the distance between the upper and lower die to a suitable location, while recognizing the play button machine from top to bottom axis no obvious dislocation (to ensure coaxial degrees).
b. products hit the cloth on the stapler is completed, the intensity of metal button values should be compliance, without instrumentation, in principle, the gap between button and cloth in order to nail plugs not enter, pull off button does not prevail.
4. At the end of the device configuration
a. emergency button holes to play before the fabric to be, but the holes can not be opened too large, otherwise the product will be separated from the whole of fastening the pull-out,
b. According to the thickness of fabric can choose a long piccolo, the length of claws, some of the products increase the length of nails and glue mesons stapler.
5. Product stapler when the note
a. After all products stapler can not be deformed, in particular, the product surface, diamond pieces, eight-run hole, emergency button spring line, surface Flute "Block Flute", button pearls first hit big, nail-free blast of space and so on.
b. After a certain amount of product binding, repeated "hit-mode set-up" work to confirm correct continued after stapler.
2. Metal button knowledge
1. Raw materials
a. copper compound copper content, the thickness?
A: Different labels in different copper content of copper present, commonly used in copper industry, there are buttons H62 copper (copper content 60.5-63.5), H65 Cu (63.5-68.0), H68 copper (67.0-70.0), copper strip thickness according to product requirements, depending on the thickness of copper strip used in the current company: 0.16mm-0.80mm between.
b. alloy composition of raw materials?
A: Currently, companies are using a 3C # zinc alloy whose main ingredient is zinc and aluminum, followed by magnesium, copper, iron, lead, cadmium, tin.
c. whether the above-mentioned raw materials had Needle machine, too Needle machine can be had several class?
A: The raw materials can be too Needle machine, over-machine materials series, as the product of the label, the product over the number of machines, products, machine placed over the manner and Needle machine models may be different.
d. Are there test report?
A: The raw material suppliers to provide quality assurance laboratory book or report card, and so can check the chemical composition and pilot projects related to value.
2. Electroplating colors
a. Plating Color Are there reference to international color card?
A: At present, electroplating factory only "Luc international standard plating color cards."
b. Plating color can achieve environmental test?
A: The Product plating color can achieve environmental test requirements.
c. Plating color will fade?
A: As time goes by, electroplating products affected by climate, environment and operation conditions affect the color contrast with the last plating there will be differences, all plating products do not package "washing", such as coating the surface of the guests right buttons have special requirements, the need a single before the next can be considered after power-do "high-power rack with disabilities," "anti -
Acid strength rack "protection.
d. whether the matter sorted out Zuse Plating color board color plating?
Answer: At present, electroplating factories for manual operation, the master control of electroplating additives and electroplating time, not like a foreign computer control of the plating process, we can not guarantee color plates with the Zuse plating, and even with the shipment there will be a different color tank plating can only be guaranteed with the Color of the similarity in the eight to Jiucheng, when the shade guide and the substrate and electrical products were not accompanied by comparable similarity to decline.
3. The intensity of product value problems
a. the intensity of the value of products according to the product structure is different, testing different methods are: pressure, tension, sustained force, damaging the value of the points.
b. The intensity of the value of the pressure, pull the value of electroplating color when the product will also be different from non-sustained force, damaging a result of materials used in products vary by thickness, concrete strength values refer to the company about the criteria.
4. Why some emergency button next three efforts to tight?
Answer: a. The company's products has its own standard size, as long as the intensity values within the tolerance range will not be much difference.
b. emergency metal button of the pull, the pressure value is a result of the different plating colors differ, such as the power of the lightest color, contrast, black old, dumb power of color than the tight, water-skiing can take products off methods to solve, followed by the product when the thickness of cloth stapler, stapler whether the products after the deformation (such as elastic after playing larger size) has the relationship between
c. If guests have special requirements on the intensity values, if necessary, may be improved in size from products
5. Products can be environmentally friendly?
A: The products can be environmentally friendly, but customers are required before the next single, the company from raw materials, production processes under control to be guaranteed.
6. Corn Products stapler why the letters after the burst phenomenon?
Answer: a. the thickness of materials and products, English mold engraving depth, post-mold processing (Lee angular Province slip), of
b. whether the corns with the play mode to play mode shape matching and adjust the height is correct.
7. Alloy cap nails sticking drilling products are playing out after drilling, diamond pieces?
Answer: a. and products related to the structure, in principle, alloy cap nail products to be mold rather than the stick pack drill drill, drill and shape, especially compared to more than 40% of diameter.
b. with the sticky glue used in the resilience of drilling related to a small number of die with the play materials and design.
8. Fuel injection and a granular surface Diaoqi foreign body?
Answer: a. Fuel Injection Products colliding with each other due to friction, especially the surface Flute Flute I would finish so bad, so in principle the application of fuel injection products packaged into plastic bags, copy paper,
b. injection surface of the granular foreign body is painted or product residue on the surface covered by the original debris was caused by paint.

From: http://www.metalbutton.net

Leather label  Back newslist >>